BLOG 15 What’s Wrong With Today’s Gasoline
Trail Stoves?
by Cliff Jacobson
My favorite trail stove is the long defunct Optimus
111B. Known for its power,
simplicity and reliability, the B still retains a strong following. One of my B’s is over 50 years old and though it’s been hammered to death on
scores of northern trips, it still runs fine. I can’t say the same for some
modern “tinker toy” (two-piece) stoves I’ve used. Here’s why:
 |
| Ciff frying fish on an Optimus 111B stove. Fond du Lac River, Saskatchwan |
Two-piece stoves have a separate fuel
tank and armored fuel line. You must connect the line to the tank every time
you use the stove—then disconnect it afterwards. This constant connect/disconnect
cycle wears the connector and/or O-ring and in time, fuel may leak here. Foreign matter can also become lodged
in the valve or connector when the stove is packed away. If this happens, it’s
game over—you’d best know how to build a fire! Some years ago, my MSR XGK sprang a leak while running hard. Gas flamed five feet high!
Fortunately, the stove was sitting on a rock near the lake. I kicked it hard
and it went sailing into the water, never to be seen again. George Drought, a
Canadian paddler of some fame (George invented the “tundra tunnel”, featured in
my book, “Expedition Canoeing”), had a similar experience on the Back River in
Canada’s arctic. He suffered serious burns and had to be air evacuated out.
This said, two-piece stoves are
remarkably safe. Those that report problems tend to cook for large groups,
which means bigger pots, longer running times and hotter tanks. Still, given equal materials, a one
piece stove will be more trouble-free than a two piece stove.
 |
| Cliff: Primus Omni-fuel stove. Note pot cover used for stove support |
WHY
TWO PARTS TO PUT TOGETHER?
The idea of splitting a stove into
two parts—burner/fuel line and fuel bottle/pump assembly—began as an
advertising gimmick. Let’s say that each of the two parts weigh one pound. The
manufacturer can (will!) list only the weight of the stove but not the weight
of the tank and pump. Twisted thinking? Yes. But lightweight sells and most buyers won’t have a clue.
The advantage of a two-piece
design is that the stove can have a long fuel delivery tube that will keep the
tank away from the hot burner. This is a good thing, especially, if you use
large pots that reflect heat onto the tank. Ironically, most fuel lines are too
short—they don’t allow enough space between the burner and tank—so for safety,
you should ALWAYS use the aluminum wind-screen that separates the two. Aluminum liter bottles (tanks) are not as strong as the heavy brass and steel tanks
of yore. Over-pressurize one and it may blow—which is what happened to George Drought
on the Back River.
Some self-contained stoves, like
the Optimus 111B, 8R and Phoebus 625 have a mechanical jet-cleaning device. Turn
the adjuster knob and a gear-driven needle pokes up through the jet and removes
carbon build-up. Compare this to
the engineering “marvels” used on modern “tinker toy” stoves:
 |
| L to R: Wire jet-cleaner, "Magnetic MIracle", weighted cleaning needle |
·
The “magnetic miracle: A magnet pushes a weighted cleaning
needle through the jet. Works great. That is until the needle shaft carbons
up and the needle begins to stick. If it sticks while the stove is
running hot, the needle may weld itself to the burner. It’s happened twice to
me with two different stoves from the same manufacturer! I removed the needle and now use the
manual cleaning tool pictured above.
·
The “shaker jet”: Vigorously shake the
stove and a weighted needle slides up and down through the jet. Same problem as above—if the stove
carbons up the needle may stick and weld.
Magnetic cleaning devices and
shaker jets are handy but they may not have enough power to push a heavily
carboned cleaning needle into position. They are fine for casual use, but can
be problematic on expeditions where stoves take a beating.
·
The old brass and steel tanks on Primus and
Optimus stoves had a spring-loaded safety valve in the cap. If the tank became
over-pressurized by heat, the safety valve would blow. I’ve experienced this
several times with my 111B and Primus 71 stoves. It’s not a spectacular show—a
thin stream of gas squirts from the safety hole in the cap, that’s all. The
remedy is to turn off the stove and allow it to cool. The valve cap will re-set
itself in a few minutes. Tinker
toy stoves don’t have re-settable safety valves!
CLEANLINESS
Just turn off a one-piece stove,
release the pressure, then pack it way. No need to unhook a fuel line (and get
gas on your hands) or to fold carbon-black burner supports.
GOOFY
WIND-SCREEN
The old self-contained stoves had
real windscreens. Modern two-piece stoves have flimsy aluminum-foil deflectors
that catch grease and fly well in wind.
IN
SUMMARY
The old one-piece stoves were
heavier (weight could be reduced with modern materials) than modern two-piece
stoves but they were more rugged and reliable. They didn’t have to be
assembled, disassembled or cushioned from impact in transit. There was no
danger of foreign material getting into an open connector or valve. They had
fewer parts and were easier to maintain in the field. Some self-contained
models, like the Optimus 111B and 8R were encased inside a hinged, metal box. Just
open the box, pull out the burner and you were good to go. What could be easier?
Cliff
Jacobson
www.cliff-jacobson.com
No comments:
Post a Comment